Mystery


Dave’s Mystery Machine

Dave sends:
Have a look at this motor I picked up! It has been sleeved down, oil pump and dip stick sealed up and a strange set up indeed. I thought it might be a M52-53 Ural motor as the bore is about 70mm and stroke 68mm. The gearbox has 3 speeds and the heads have been machined squarish shape, also strange inlet size….. any ideas? it looks to me there was a magneto attached to the front of the crank? Seems like it to me. I don’t think it’s a racer but maybe a boat motor or some kind of set up? Strange that’s for sure. the valve springs are real light, you can push them in with your fingers. Strange thing is the inlet are small and have been reduced, see the threaded set up?

If I was going to do a race motor why make the inlet smaller? You would go bigger. Can’t find any place to check the oil? Strange, also the cylinders are not like regular Ural as there the lower fin is missing (6 fins on the cylinder instead of 7 on a regular Ural. Also the bore seems to be 71mm or close to it, stroke I think is 68mm. Could it have been some factory experiment? Maybe some kind of strange craft? Strange why it has been made to about 500cc though, I would think if it was a boat motor or craft of some kind you would just leave it 650cc.

Also the sump plug is on the side of the sump directly under the dip stick area, I had a good look and it seems the sump is original and has not been welded or repositioning of the sump plug. The sump plug is real small too, I did see a number stamped above the left cylinder 61 so my guess that’s the year of the original motor? If you find out something let me know. I had a look at a Ural C120 racer, hard to tell but look a bit like that motor. Don’t think it’s a car motor, the heads are special made, note the inlet, no bolts to hold on the carbs.

The top plate screw holes are very small and would not hold anything but a simple cover/breather. The motor has been used so I know it was a runner.

I’m certain now it’s some kind of racer or speed motor? Not sure what though? The gearbox is a 3 speed, the cylinders and heads are special, not stock Ural. A 3 speed box is not exactly a speed machine, so why? The flywheel is a special lightened type with 12 or more mounting studs, the clutch is a all metal type plate with 7 plates all special racing metal type (I think there should be 8, maybe 1 is missing 🙁

The motor seems to be balanced as the clutch plates have align marks. See the crank shaft… strange, the con rods are not stock either. I took the sump off, what a sight, no oil pump and a lot of alloy has been cut out from inside. It’s driving me mad, can’t figure out how the motor is fed oil or to check the oil level! After looking at some old pics of BMW’s, I’m starting to think if this motor was supercharged? If you look at the inlet ports you will see it has a small threaded pipe, not your regular carb fitting, makes me think there was some force or pressure there??? Why thread a inlet fitting?

I’m not too sure if this was a factory motor, but at least maybe experimental motor maybe even made by a small factory not directly connected to Ural? I don’t think it was a home made job, too many special parts. I’m still trying to find out more, but maybe we will never know the truth or history? One of my ideas was it was a special sports motor made by East Germany? Just a wild guess since it came out of a East German AWO/simpson 250cc, tomorrow I will have a look at the frame it came out of. Could it be some kind of BMW????

I checked the gearbox, top gear has what I believe is 0.75:1 which means is a very fast top ratio. One revolution of the gearbox input shaft and the output shaft turns 1.25 times. I never counted the gear teeth so that ratio is a rough est. I now have the final drive, but I think it maybe not from this project? At least from the AWO the motor came from, good chance the motor was not meant for the AWO and someone had a motor to fit! Anyway the final drive is about 4.6:1 not exactly fast. More checking is needed.

-Dave

note from Peter in Sweden:

The mystery engine is so very strange. No oil pump? It almost rules out high power. With so small diameter inlets it was either very low power engine or it was supercharged. Anyway it is an interesting piece.
Best Regards,
Peter

Photos ©David Mayne 2004

(July 2015)This page has been resurrected from the old website, we know you’re out there Dave! It would be good to hear if you have done anything with this mystery machine of yours.

© b-cozz.com 2017

top

8 thoughts on “Mystery

  1. JD

    I’ve been looking at and thinking about this mystery motor of Dave’s for 6 years now. I agree with Eugene, if it’s a 500cc it;s a 500cc. It’s IMZ or from Surpukhov (or a bit of both, maybe even partly a 500cc BMW)…. but whatever it is, I think it might have indeed been a record attempt machine, perhaps even supercharged. It all seems to point to it.
    It would be great to find out more. Dave? Anyone?

    Reply
  2. JD

    Hi Paul, good you are interested! I presume it was a shaft drive, you can see the gearbox output shaft in the usual position. BSF, I doubt it. BMW were metric and so were the Soviet Opposites. But anything is possible, especially on a kitchen designers thing like this one, perhaps even a pre-war lathe or tooling from England or the USA? Perhaps Mr Wiggins might add his thoughts. 💡

    Reply
  3. paul milsom

    hi just picked up on your mystery motor,, interesting … you don’t say what the final drive is, presumably shart? what are the thread forms used, they look like BSF … ongoingly curious….. paul

    Reply
  4. Evgenny, edited by JD

    comment by Eugene in Russia :

    “Also, about your Mystery 500 cc opposite, Even if the engine has 61, which is likely a production year, there’s little doubt it was a good re-built of M-52/M-53 road racing modification into… the Shumilkin Komet! 🙂 Remember trans. ratio .0.75? Threaded ducts and a big tooth-wheel with upper engine’s casing cut open? – A charger drive, not a generator. Some of 1930-s BMW record machines had reversed exhaust and intake ports: pipes on the rear, charger manifold coming from front wheel area. No oiling system? No need for it, if the engine was meant for record setting, probably with an aero-coat or fish-like casing (The World’s fastest Indian or Ural in this case). The record engines as well as other motocross engines were dismantled every race for cleaning and checking. I think they used if not a dry sump but got rid of all parts for weight considerations, leaving oiling carried out out by crankshaft splashing. I’d like to see how it works or perhaps even ride it.”

    Reply
  5. zeze

    An impressive share! I have just forwarded this onto a friend who
    was doing a little research on this. And he actually ordered
    me dinner simply because I found it for him… lol. So allow me to reword this….
    Thank YOU for the meal!! But yeah, thanks for
    spending the time to talk about this subject here on your website.

    Reply
  6. JD

    Whatever it is it has fixed ignition timing, no timing turnplate on the distributor, it’s fixed. Whether the timing was retarded for a tractor or advanced for a racer? Maybe we’ll hear from Dave again. Hi Dave!

    Reply

Leave a Reply

Your email address will not be published. Required fields are marked *

This site uses Akismet to reduce spam. Learn how your comment data is processed.